Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
The author is making a number of great points on the subject of How to Install a Bathtub Yourself overall in this article below.
Mounting a bathtub isn't specifically rocket science, yet it does require solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably hard job. If the old bathtub is readily obtainable, the project can move speedily; if you have to open up a wall to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. See to it you have certified on your own for the job and also fit attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you mount a brand-new bathtub in your shower room if you have actually already purchased a brand-new bathtub and don't require to transform the setup of your previous water supply pipes.
Your tools and also product checklist ought to make up the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the restricted access that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Secure the faucet in position with the producer provided backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the required placement. The wood boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the spirit level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Fill up the bath tub and additionally check the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait up until the bath tub has actually been utilized a minimum of when as this will settle it right into its last placement.
Preparing for the Setup
To start with, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break a rigid seal, causing the water to penetrate the wall between the bath and the tiling, resulting in complications with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill the tub with water prior to securing, to enable the motion experienced when the bathtub is in use. The sealant can crack fairly very early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about How to Install a Bathtub Yourself? Create a remark directly below. We'd be interested to listen to your reactions about this page. We are looking forward that you visit us again before long. Kindly take a moment to distribute this post if you enjoyed reading it. Thank you so much for going through it.
Book Services
Report this page